Page MenuHomePhabricator

Installation issues on PowerEdge R440 Ganeti servers with buster / firmware update needed
Closed, ResolvedPublic

Description

I tried to reinstall ganeti2010 with buster, but I'm getting a strange installer failure; over the serial console I can see that the d-i image and the initrd are being served (and it's also showing up in the logs of the install* server), but after that the system reboots into the installed system.

This might be an issue with the new kernel and outdated firmware. Could you please upgrade firmware on this host (and if possible also NIC firmware)? The server currently has no instance and can be powered down any time.

  • ganeti2007
  • ganeti2008
  • ganeti2009
  • ganeti2010
  • ganeti2011
  • ganeti2012
  • ganeti2013
  • ganeti2014
  • ganeti2015
  • ganeti2016
  • ganeti2017
  • ganeti2018

Event Timeline

Papaul triaged this task as Medium priority.Dec 1 2021, 3:52 PM
BIOS Version 	1.7.0
iDRAC Firmware Version 	3.30.30.30

this is complete

BIOS Version 	2.12.2
iDRAC Firmware Version 	5.00.10.20

Thanks for the quick turnaround, much appreciated! I'll kick off another reimage attempt tomorrow.

I have good and bad news :-) The good news is that the firmware update made the Buster installer work \o/. The bad news is that we have nine more servers of that batch, so those will likely all need a firmware update as well. Do you prefer to reuse/extend this task or should I rather create new ones as I run into them?

I have good and bad news :-) The good news is that the firmware update made the Buster installer work \o/. The bad news is that we have nine more servers of that batch, so those will likely all need a firmware update as well. Do you prefer to reuse/extend this task or should I rather create new ones as I run into them?

Unfortunately I was right and I ran into the same issue with ganeti2009 as well. Can you please also update it? Or alternatively I can also open a new task. The server can be powered off any time.

MoritzMuehlenhoff renamed this task from Installation issues on ganeti2010 with buster / firmware update to Installation issues on ganeti2009/2010 with buster / firmware update needed.Dec 2 2021, 12:11 PM

I prefer to just reuse/extent the task by adding the nodes in the description like i did for ganeti2009 and 2010 so we keep better tack.

Thanks

I prefer to just reuse/extent the task by adding the nodes in the description like i did for ganeti2009 and 2010 so we keep better tack.

Thanks

Sounds good to me, I'll extend the task description as I run into further affected servers.

MoritzMuehlenhoff renamed this task from Installation issues on ganeti2009/2010 with buster / firmware update needed to Installation issues on PowerEdge R440 Ganeti servers with buster / firmware update needed.Dec 3 2021, 11:21 AM
MoritzMuehlenhoff updated the task description. (Show Details)

And one more, added to the task description and ready to power off any time. I should have made an advent calendar out of these, one surprise server for each day of December so far :-)

One more; ganeti2016. Ready to be powered off any time.

One more; ganeti2012. Ready to be powered off any time.

One more; ganeti2013. Ready to be powered off any time.

One more; ganeti2014. Ready to be powered off any time.

One more; ganeti2008. Ready to be powered off any time.

One more; ganeti2017. Ready to be powered off any time.

One more; ganeti2018. Ready to be powered off any time.

One more; ganeti2015. Ready to be powered off any time.

One more; ganeti2007. Ready to be powered off any time. It's the last one \o/

Thanks Papaul for the swift turnarounds, much appreciated.

@MoritzMuehlenhoff no problem closing this task now