Change Details

== ms-be1013.eqiad.wmnet The first 5 steps should be completed by the service owner that is returning the server to DC-ops (for reclaim to spare or decommissioning, dependent on server configuration and age.) Steps for service owner: [x] - all system services confirmed offline from production use [x] - set all icinga checks to maint mode/disabled while reclaim/decommmission takes place. [x] - remove system from all lvs/pybal active configuration [x] - any service group puppet/hiera/dsh config removed [x] - remove site.pp, replace with role(spare::system) [x] - unassign service owner from this task, check off completed steps, and assign to @robh for followup on below steps. Steps for DC-Ops: The following steps cannot be interrupted, as it will leave the system in an unfinished state. **Start non-interrupt steps:** [] - disable puppet on host [] - power down host [] - update netbox status to Inventory (if decom) or Planned (if spare) [] - disable switch port [] - switch port assignment noted on this task (for later removal) [] - remove all remaining puppet references (include role::spare) [] - remove production dns entries [] - puppet node clean, puppet node deactivate (handled by wmf-decommission-host) [] - remove dbmonitor entries on neodymium/sarin: sudo curl -X DELETE https://debmonitor.discovery.wmnet/hosts/${HOST_FQDN} --cert /etc/debmonitor/ssl/cert.pem --key /etc/debmonitor/ssl/server.key (handled by wmf-decommission-host) **End non-interrupt steps.** [] - system disks wiped (by onsite) [] - IF DECOM: system unracked and decommissioned (by onsite), update racktables with result [] - IF DECOM: switch port configration removed from switch once system is unracked. [] - IF DECOM: add system to decommission tracking google sheet [] - IF DECOM: mgmt dns entries removed. [] - IF RECLAIM: system added back to spares tracking (by onsite) == ms-be1014.eqiad.wmnet The first 5 steps should be completed by the service owner that is returning the server to DC-ops (for reclaim to spare or decommissioning, dependent on server configuration and age.) Steps for service owner: [x] - all system services confirmed offline from production use [x] - set all icinga checks to maint mode/disabled while reclaim/decommmission takes place. [x] - remove system from all lvs/pybal active configuration [x] - any service group puppet/hiera/dsh config removed [x] - remove site.pp, replace with role(spare::system) [x] - unassign service owner from this task, check off completed steps, and assign to @robh for followup on below steps. Steps for DC-Ops: The following steps cannot be interrupted, as it will leave the system in an unfinished state. **Start non-interrupt steps:** [] - disable puppet on host [] - power down host [] - update netbox status to Inventory (if decom) or Planned (if spare) [] - disable switch port [] - switch port assignment noted on this task (for later removal) [] - remove all remaining puppet references (include role::spare) [] - remove production dns entries [] - puppet node clean, puppet node deactivate (handled by wmf-decommission-host) [] - remove dbmonitor entries on neodymium/sarin: sudo curl -X DELETE https://debmonitor.discovery.wmnet/hosts/${HOST_FQDN} --cert /etc/debmonitor/ssl/cert.pem --key /etc/debmonitor/ssl/server.key (handled by wmf-decommission-host) **End non-interrupt steps.** [] - system disks wiped (by onsite) [] - IF DECOM: system unracked and decommissioned (by onsite), update racktables with result [] - IF DECOM: switch port configration removed from switch once system is unracked. [] - IF DECOM: add system to decommission tracking google sheet [] - IF DECOM: mgmt dns entries removed. [] - IF RECLAIM: system added back to spares tracking (by onsite) == ms-be1015.eqiad.wmnet The first 5 steps should be completed by the service owner that is returning the server to DC-ops (for reclaim to spare or decommissioning, dependent on server configuration and age.) Steps for service owner: [x] - all system services confirmed offline from production use [x] - set all icinga checks to maint mode/disabled while reclaim/decommmission takes place. [x] - remove system from all lvs/pybal active configuration [x] - any service group puppet/hiera/dsh config removed [x] - remove site.pp, replace with role(spare::system) [x] - unassign service owner from this task, check off completed steps, and assign to @robh for followup on below steps. Steps for DC-Ops: The following steps cannot be interrupted, as it will leave the system in an unfinished state. **Start non-interrupt steps:** [] - disable puppet on host [] - power down host [] - update netbox status to Inventory (if decom) or Planned (if spare) [] - disable switch port [] - switch port assignment noted on this task (for later removal) [] - remove all remaining puppet references (include role::spare) [] - remove production dns entries [] - puppet node clean, puppet node deactivate (handled by wmf-decommission-host) [] - remove dbmonitor entries on neodymium/sarin: sudo curl -X DELETE https://debmonitor.discovery.wmnet/hosts/${HOST_FQDN} --cert /etc/debmonitor/ssl/cert.pem --key /etc/debmonitor/ssl/server.key (handled by wmf-decommission-host) **End non-interrupt steps.** [] - system disks wiped (by onsite) [] - IF DECOM: system unracked and decommissioned (by onsite), update racktables with result [] - IF DECOM: switch port configration removed from switch once system is unracked. [] - IF DECOM: add system to decommission tracking google sheet [] - IF DECOM: mgmt dns entries removed. [] - IF RECLAIM: system added back to spares tracking (by onsite)

These are old hosts that need decom. First order of things is getting them to weight 0 in swift, then we can proceed with regular decom.== ms-be1013.eqiad.wmnet The first 5 steps should be completed by the service owner that is returning the server to DC-ops (for reclaim to spare or decommissioning, dependent on server configuration and age.) Steps for service owner: [x] - all system services confirmed offline from production use [x] - set all icinga checks to maint mode/disabled while reclaim/decommmission takes place. [x] - remove system from all lvs/pybal active configuration [x] - any service group puppet/hiera/dsh config removed [x] - remove site.pp, replace with role(spare::system) [x] - unassign service owner from this task, check off completed steps, and assign to @robh for followup on below steps. Steps for DC-Ops: The following steps cannot be interrupted, as it will leave the system in an unfinished state. **Start non-interrupt steps:** [] - disable puppet on host [] - power down host [] - update netbox status to Inventory (if decom) or Planned (if spare) [] - disable switch port [] - switch port assignment noted on this task (for later removal) [] - remove all remaining puppet references (include role::spare) [] - remove production dns entries [] - puppet node clean, puppet node deactivate (handled by wmf-decommission-host) [] - remove dbmonitor entries on neodymium/sarin: sudo curl -X DELETE https://debmonitor.discovery.wmnet/hosts/${HOST_FQDN} --cert /etc/debmonitor/ssl/cert.pem --key /etc/debmonitor/ssl/server.key (handled by wmf-decommission-host) **End non-interrupt steps.** [] - system disks wiped (by onsite) [] - IF DECOM: system unracked and decommissioned (by onsite), update racktables with result [] - IF DECOM: switch port configration removed from switch once system is unracked. [] - IF DECOM: add system to decommission tracking google sheet [] - IF DECOM: mgmt dns entries removed. [] - IF RECLAIM: system added back to spares tracking (by onsite) == ms-be1014.eqiad.wmnet The first 5 steps should be completed by the service owner that is returning the server to DC-ops (for reclaim to spare or decommissioning, dependent on server configuration and age.) Steps for service owner: [x] - all system services confirmed offline from production use [x] - set all icinga checks to maint mode/disabled while reclaim/decommmission takes place. [x] - remove system from all lvs/pybal active configuration [x] - any service group puppet/hiera/dsh config removed [x] - remove site.pp, replace with role(spare::system) [x] - unassign service owner from this task, check off completed steps, and assign to @robh for followup on below steps. Steps for DC-Ops: The following steps cannot be interrupted, as it will leave the system in an unfinished state. **Start non-interrupt steps:** [] - disable puppet on host [] - power down host [] - update netbox status to Inventory (if decom) or Planned (if spare) [] - disable switch port [] - switch port assignment noted on this task (for later removal) [] - remove all remaining puppet references (include role::spare) [] - remove production dns entries [] - puppet node clean, puppet node deactivate (handled by wmf-decommission-host) [] - remove dbmonitor entries on neodymium/sarin: sudo curl -X DELETE https://debmonitor.discovery.wmnet/hosts/${HOST_FQDN} --cert /etc/debmonitor/ssl/cert.pem --key /etc/debmonitor/ssl/server.key (handled by wmf-decommission-host) **End non-interrupt steps.** [] - system disks wiped (by onsite) [] - IF DECOM: system unracked and decommissioned (by onsite), update racktables with result [] - IF DECOM: switch port configration removed from switch once system is unracked. [] - IF DECOM: add system to decommission tracking google sheet [] - IF DECOM: mgmt dns entries removed. [] - IF RECLAIM: system added back to spares tracking (by onsite) == ms-be1015.eqiad.wmnet The first 5 steps should be completed by the service owner that is returning the server to DC-ops (for reclaim to spare or decommissioning, dependent on server configuration and age.) Steps for service owner: [x] - all system services confirmed offline from production use [x] - set all icinga checks to maint mode/disabled while reclaim/decommmission takes place. [x] - remove system from all lvs/pybal active configuration [x] - any service group puppet/hiera/dsh config removed [x] - remove site.pp, replace with role(spare::system) [x] - unassign service owner from this task, check off completed steps, and assign to @robh for followup on below steps. Steps for DC-Ops: The following steps cannot be interrupted, as it will leave the system in an unfinished state. **Start non-interrupt steps:** [] - disable puppet on host [] - power down host [] - update netbox status to Inventory (if decom) or Planned (if spare) [] - disable switch port [] - switch port assignment noted on this task (for later removal) [] - remove all remaining puppet references (include role::spare) [] - remove production dns entries [] - puppet node clean, puppet node deactivate (handled by wmf-decommission-host) [] - remove dbmonitor entries on neodymium/sarin: sudo curl -X DELETE https://debmonitor.discovery.wmnet/hosts/${HOST_FQDN} --cert /etc/debmonitor/ssl/cert.pem --key /etc/debmonitor/ssl/server.key (handled by wmf-decommission-host) **End non-interrupt steps.** [] - system disks wiped (by onsite) [] - IF DECOM: system unracked and decommissioned (by onsite), update racktables with result [] - IF DECOM: switch port configration removed from switch once system is unracked. [] - IF DECOM: add system to decommission tracking google sheet [] - IF DECOM: mgmt dns entries removed. [] - IF RECLAIM: system added back to spares tracking (by onsite)